Skip to content
Request a Quote

Industries Served · Sector Index 01 / 06

Industries where ProEdge Wire is already on the AVL — six regulated sectors, one supplier, one published lead-time clock.

ProEdge Wire produces custom-drawn wire, stranded cable, and specialty alloy conductors for OEM buyers operating under the documentation discipline of AS9100D, PPAP/IMDS reporting, full material traceability, and FDA-cleared device assemblies. Every sector below is served from the same two Cleveland-area facilities, against the same 14-day custom-order clock.

  • 14 Day standard lead time on custom wire orders
  • 99.4% On-time shipment rate, trailing 18 months
  • 1,800+ Active SKUs across 47 alloy families
Request a Quote Review Capabilities

Sector Index · 01

Six industries. Six spec sheets. One supplier reviewed before every quote.

A datasheet-style map of the regulated sectors ProEdge Wire is already qualified into. Each panel names the procurement pain, the typical spec envelope, and the entry point for engineering readers who want to drill into the per-sector detail page.

  1. 01

    Automotive · Tier 1 Suppliers

    High-volume copper and copper-alloy conductors for harnesses, sensor leads, and EV battery interconnects — with full PPAP and IMDS reporting on every shipment.

    Alloys
    OFC Cu, Cu-Ag, Cu-Sn, Ni-plated Cu
    Diameter
    0.008" – 0.250"
    Tolerance
    ±0.001"
    Docs
    PPAP · IMDS · C of C · RoHS
    Open sector spec sheet →
  2. 02

    Aerospace & Defense · ITAR

    Mission-critical conductors for avionics harnesses, flight-control cabling, and ITAR-registered defense prime assemblies — released against AS9100D with full material traceability.

    Alloys
    Cu, Cu-Ni, Ni, Ni-Cr, Inconel
    Diameter
    0.005" – 0.125"
    Tolerance
    ±0.0005"
    Docs
    AS9100D · C of C · ITAR-controlled
    Open sector spec sheet →
  3. 03

    Medical Devices · FDA-Cleared

    Precision conductors for diagnostic leads, catheter reinforcement, surgical instrumentation, and patient-monitoring cabling — built on a documented quality system with lot-level traceability.

    Alloys
    SS 304/316, MP35N, Pt-Ir, Cu
    Diameter
    0.003" – 0.062"
    Tolerance
    ±0.0005"
    Docs
    Lot trace · C of C · RoHS · biocompatibility ref.
    Open sector spec sheet →
  4. 04

    Industrial Automation

    Robotics, motion-control, and high-flex life-cycle cabling for factory-floor OEMs and system integrators — stranded and rope-lay constructions rated for continuous flex.

    Alloys
    Bare Cu, tinned Cu, Ni, Cu-Steel composite
    Diameter
    0.015" – 0.500"
    Tolerance
    ±0.002"
    Docs
    C of C · RoHS · REACH
    Open sector spec sheet →
  5. 05

    EV & Powertrain

    High-purity copper conductors and stranded assemblies for traction motors, battery packs, charging harnesses, and power-electronics interconnects — high-conductivity alloys at production volumes.

    Alloys
    OFC Cu, Cu-Ag, Cu-Sn, Al-clad Cu
    Diameter
    0.020" – 0.500"
    Tolerance
    ±0.001"
    Docs
    PPAP · IMDS · C of C · RoHS
    Open sector spec sheet →
  6. 06

    Heavy Industrial

    Large-diameter conductors and specialty alloys for mining, rail, energy, and heavy-equipment OEMs — long runs of nickel, stainless, and high-temp exotic conductors.

    Alloys
    Ni, SS 302/304/316, Inconel, Monel
    Diameter
    0.040" – 0.500"
    Tolerance
    ±0.002"
    Docs
    C of C · Mill cert · RoHS
    Open sector spec sheet →

Capability Lanes · 02

What every sector on the previous page is buying — the four capability lanes behind 1,800+ active SKUs.

Six regulated industries run through the same four core processes on the Cleveland floor. This is the production vocabulary an applications engineer will speak when they pick up your RFQ — and the vocabulary a Tier 1 or defense buyer should expect to hear.

Multi-die wire drawing bench at the Cleveland facility
Lane 01

Draw

Single- and multi-die cold drawing from 0.500" rod down to 0.003" fine wire, holding ±0.0005" diameter tolerance across 47 stocked alloys.

  • Range0.003" – 0.500"
  • Tolerance±0.0005"
  • Alloys47 stocked families
Bright annealing furnace for stress-relief on drawn wire
Lane 02

Anneal

In-line and batch annealing for conductivity tuning, stress relief, and dead-soft temper — calibrated to the conductivity and elongation target your print specifies.

  • AtmosphereBright / inert / forming gas
  • RangeCu, Ni, SS, exotic
  • TestConductivity + elongation per spool
Seven-spool wire strander producing a stranded conductor
Lane 03

Strand & Bunch

Concentric, rope-lay, and bunch constructions from 7-strand through 1,800+ strand counts — built for high-flex life cycle or low-DC-resistance power transmission.

  • LayConcentric · Rope · Bunch · SZ
  • Counts7 through 1,800+
  • AWG44 AWG – 4/0 equivalent
In-line plating line for tinned, nickel, and silver finishes
Lane 04

Plate & QA

Tin, nickel, silver, and gold plating over copper and alloy substrates, closed by a QA lab that holds every spool against diameter, conductivity, elongation, and surface-finish limits.

  • FinishesSn · Ni · Ag · Au
  • QALab on every shift
  • DocsPPAP · C of C · IMDS

Audit-Grade Numbers · 03

The numbers behind the sector list.

  • 99.4% On-time shipment, trailing 18 mo. Audit · Global Logistics Review · Q1 2025
  • 640+ Active B2B accounts served 91% retention · 5-year trailing
  • PPAP · IMDS · C of C Documentation pack per shipment Standard on every line · AS9100D
  • ISO 9001 · AS9100 · RoHS Certifications renewed Feb 2025 ISO 9001:2015 · AS9100D · RoHS

Regulatory Statement · 04

If your buyer needs the paperwork before the wire, you are in the right place.

A defense prime's AVL review and an FDA-cleared device OEM's DHF both start in the same place: the supplier's quality manual, the certs on the wall, and the documentation pack that travels in the box with every spool. ProEdge Wire is built for that buyer. Our standard shipment ships with the Certificate of Conformance, the PPAP package (where applicable), and the IMDS submission already on file — so your incoming-inspection team is reviewing part numbers, not chasing paperwork.

AS9100D and ISO 9001:2015 cover the system. RoHS compliance covers the substance. Eleven in-house metallurgists and a nine-person applications engineering group cover the part your print actually describes. Every RFQ is reviewed by an engineer before it becomes a quote — not after — so the price you see is the price against a feasible process, not a wish list.

For ITAR-controlled defense work we operate inside a documented export-control program. For medical device OEMs we provide full lot-level material traceability and biocompatibility-supporting documentation referenced to the relevant ISO 10993 surface-contact standards. We do not hold NADCAP or ISO 13485 and we do not pretend otherwise — if your program needs those, we will say so on the first call.